基于ANSYS Workbench的越野汽车轮毂有限元分析及优化

文章利用三维软件Creo建立轮毂的三维模型,导入ANSYS Workbench后进行网格化,形成有限元计算模型并进行计算,得出其极限工况时的应力、变形结果。依据分析计算结果,提出结构改进方案并进行验证计算,为优化设计提供重要的理论依据。     

Collision course? The North Airfield Safety Study at Los Angeles International Airport (LAX)

The LAX North Airfield Safety Study was undertaken by an Academic Panel consisting of the present authors, and was based in large part on a simulation that was conducted at FutureFlight Central at NASA Ames Research Center. The primary aim of the study was “to estimate as specifically as possible the level of future safety associated with several geometrical configurations of the LAX North Airfield.” This paper describes the study, and how it combined information from human-in-the-loop simulations at NASA with historical data from LAX and other US airports about runway incursions and collisions. The analysis indicated that, even under its existing physical layout, LAX North would experience very low risk of runway collisions at traffic levels projected for 2020. That risk could be reduced by about half if the North Airfield runways were reconfigured, and some reconfigurations would also add appreciably to the operational efficiency of the airport. But because the “baseline” level of risk is so low, the Study concluded that “it would be difficult to construct a compelling case on safety grounds alone for reconfiguring the North Airfield.”     

A comparison of modelled and real-life driving profiles for the simulation of railway vehicle operation

A key factor in determining the performance of a railway system is the speed profile of the trains within the network. There can be significant variation in this speed profile for identical trains on identical routes, depending on how the train is driven. A better understanding and control of speed profiles can therefore offer significant potential for improvements in the performance of railway systems. This paper develops a model to allow the variability of real-life driving profiles of railway vehicles to be quantitatively described and predicted, in order to better account for the effects on the speed profile of the train and hence the performance of the railway network as a whole. The model is validated against data from the Tyne and Wear Metro, and replicates the measured data to a good degree of accuracy.     

公路隧道运营通风横通道周围流场特性研究

为研究公路隧道巷道式运营通风横通道周围的流场特性,以贵州凉风坳隧道为研究背景,利用流体力学研究软件Fluent建立隧道三维模型并进行了数值仿真计算。通过在隧道两边等风速条件下,对隧道内人行横通道以及车行横通道附近的流场特点研究,分析了运营通风横通道周围流场分布的具体特点。模拟结果表明:车行横通道与人行横通道两边流场分布基本相同;横通道内风速相对较小,约为隧道内风速的10%;不同风速下,横通道附近的速度分布和总压分布整体走势一致;两边流场相对稳定,不会进行风流和污染物的串流。     

Vehicle response-based track geometry assessment using multi-body simulation

The assessment of the geometry of railway tracks is an indispensable requirement for safe rail traffic. Defects which represent a risk for the safety of the train have to be identified and the necessary measures taken. According to current standards, amplitude thresholds are applied to the track geometry parameters measured by recording cars. This geometry-based assessment has proved its value but suffers from the low correlation between the geometry parameters and the vehicle reactions. Experience shows that some defects leading to critical vehicle reactions are underestimated by this approach. The use of vehicle responses in the track geometry assessment process allows identifying critical defects and improving the maintenance operations. This work presents a vehicle response-based assessment method using multi-body simulation. The choice of the relevant operation conditions and the estimation of the simulation uncertainty are outlined. The defects are identified from exceedances of track geometry and vehicle response parameters. They are then classified using clustering methods and the correlation with vehicle response is analysed. The use of vehicle responses allows the detection of critical defects which are not identified from geometry parameters.     

郑万高铁隧道大型机械化配套全断面法施工围岩-支护结构相互作用力学特性研究

为研究郑万高铁大型机械化配套全断面法施工围岩-支护结构相互作用力学特性,依托郑万高铁隧道现场实测数据,确定台阶法和大型机械化配套全断面法2种工法施工的围岩压力分布特征,并采用数值模拟的方法建立围岩-支护结构有限元模型,分析2种工法对围岩压力和结构内力的影响规律。研究结果表明： 1)台阶法多次施工扰动易导致支护结构和围岩之间产生空隙而发生脱空,大型机械化配套全断面法施工对围岩扰动次数少,初期支护快速封闭成环,可保证初期支护及围岩之间良好的密贴性; 2)在软弱围岩中,采用大型机械化配套全断面法施工比台阶法更有利于改善结构受力,减缓结构内部偏心受压的程度,能有效发挥拱形隧道结构承载力; 3)大型机械化配套全断面法在软弱围岩快速施工、控制支护结构变形、保证支护结构受力安全等方面具有综合优势。     

沉管隧道基槽爆破开挖作用下邻近地铁隧道力学响应

为确保邻近地铁隧道在沉管隧道基槽爆破开挖过程的安全性,通过现场实测评价地铁隧道运营现状,借助数值分析法探索地铁隧道对沉管基槽爆破开挖的力学响应特征,并制定既有隧道结构的安全判据和沉管基槽爆破振动安全距离。研究表明： 既有地铁区间隧道现状累计最大沉降为1.89 mm,近半年最大沉降速率为0.01 mm/d,均小于规范规定的控制值,隧道结构现状处于稳定状态;沉管隧道基槽爆破振动引起的地铁隧道结构最大振速为0.359 cm/s,远小于振速安全阈值（2.0 cm/s）,说明地铁结构受爆破振动影响较小,且爆破振动的安全距离为25 m; 基槽开挖应力扰动后引起的地铁隧道累计最大沉降为3.16 mm,小于位移预警值,隧道结构处于稳定状态。     

桥、隧、路、堤组合结构应用技术

为解决受周边既有环境影响下隧道出入口的展线难题,依托长沙市营盘路隧道工程实例开展系统性研究。结合桥、隧相连工程的实际特点,提出一种桥、隧、路、堤组合结构方案,并对该方案实施的可行性进行详细分析及阐述。通过运用Plaxis2D有限元软件对组合方案进行受力计算,结果表明: 护壁墙与隧道结构在位移的变化上基本达到协同变形,所设置的联系横、纵梁结构能有效地将护壁墙与隧道结构连接成整体,起到整体受力的作用。同时,在工程施工期间进行现场监测,结果显示： 大堤周边地表累计最大沉降量为15.44 mm,水平最大位移为6.72 mm,实际监测量均小于数值模拟的最大沉降量（21.34 mm）和最大水平位移（8.77 mm）。模拟结果对施工起到一定的指导作用,组合方案在满足承载力要求的前提下,最大限度地保留既有原始地貌,解决了特殊条件下的交通功能问题。     

波纹钢板套衬解决隧道衬砌掉落病害的效果分析

为解决衬砌起层剥落病害问题,提出使用波纹钢板套衬的衬砌加固方法,即使用化学锚栓将波纹钢板与衬砌混凝土连接,并在中间添加填充材料。考虑衬砌混凝土掉落时波纹钢板单独作用,波纹钢板与化学锚栓共同作用,波纹钢板、化学锚栓和填充层共同作用3种不同工况,针对3种工况建立相应的有限元数值分析模型,并对加固效果进行计算和分析。计算结果表明： 波纹钢板单独作用时结构处于最不利情况,此时波纹钢板顶部挠度为110.2 mm,应力为136.8 MPa,满足变形和受力要求; 当考虑化学锚栓和填充层的作用时,结构响应最小。     

车站基坑揭露断层带注浆加固效果数值模拟研究

为研究注浆对明挖基坑揭露断层带的加固效果,以南京地铁上元门车站基坑工程为背景,考虑基坑开挖过程中渗流场与围岩应力场的相互耦合作用,建立相应的有限元分析模型,对软弱破碎层、注浆加固带、基坑地下连续墙以及围岩所组成的耦合系统进行模拟,研究注浆加固前后围岩渗流场、位移场以及应力场的特征,最终获得基坑地下连续墙的水平位移、基坑外地表沉降、围岩塑性区分布、基坑内围岩变形以及基坑内涌水量变化规律。研究结果表明： 1）通过对基坑底部断层带的注浆加固,基坑侧向位移及基坑外地表沉降均得到有效控制,相比于注浆加固前,其最大水平位移和地表累计沉降量减小50%以上,满足工程要求; 2）基坑底部区域内塑性区范围明显减少,基坑外塑性区扩散也得到有效抑制; 3）基坑底部断层带注浆改变了渗流场分布,有效降低了基坑涌水量,基坑治理区域涌水量由最初的94 m3/h逐渐减小到4 m3/h,堵水率达96%; 4）注浆结束后现场钻孔取芯率达到75%~80%,开挖揭露大量劈裂作用形成的浆脉,验证了注浆可有效治理明挖基坑所揭露的软弱断层破碎带。